GAP驗廠簡介，GAP質量審核技術規范-裁剪問題及相關要求

人氣瀏覽: (3756) 發布時間: [2022-01-13]

GIS QA Technical Evaluation Scope
CONFIDENTIALITY: The information, comments and opinions contained in the report including any and all attached photographs, copies of reports and similar documents are for the use of the Gap Inc. business units and its subsidiary companies. Do not distribute or photocopy this report without receiving prior written consent from GIS VQM department.

Section	Q no.	Question
Cutting 裁剪	1	Check if there are proper control of pile height for cutting? 是否有檢查拉布高度？
Cutting	2	Check if the production marker with panels are properly laid flat, overlapped with proper special marker, cut by pieces using appropriate scissors/ band knife/ die cut/ lazar cut…etc.? 有無檢查嘜架是否正確的平輔，是否有重疊和標記，使用適當的剪刀/帶式刀/打孔機等？
Cutting	3	Is there proper control for matching / cutting of patterned fabrics such as plaids & stripes? (Only for plaids/ stripes) 裁剪時是否合理控制條字布和格子布使其對條對格？
Cutting	4	Is spreading methodology is found with appropriate tension; stretch /knit fabric relaxation process correct, PU and leather in correct shading separation, suitable controlled environment condition for relaxation/ temporary storage ? 是否使用適當的力來拉布以避免張力，針織布的松布程序是否正確，PU和皮革是否正確的分開色差，是否在適當的環境松布，松好的布是否儲存在受控區？
Cutting	5	Is there roving QC checking cutting accuracy? QC有無檢查裁剪的精確度？
Cutting	6	Are cut pieces properly inspected and numbered? 裁片有無檢查和編號？
Cutting	7	Does factory has good housekeeping on leftover fabric/ cut panels/ waste fabric? 對每匹布裁剩的布尾有無很好的記錄和保存，以備配片之需？
Cutting	8	Is there work-in-progress balance between cutting and production output to adequately fulfill daily production requirement? 是否有衡量裁剪和其他生產過程的產量足以達到日產能要求？
Cutting	9	Indicate fusing method used? - Hand Iron , trouser steam press, small piece fusing press, continuous roller fusing press. 燙襯用的是熨斗、蒸汽壓力機、小的熔化塊還是滾筒式熔化機？
Cutting	10	Is fusing quality acceptable, machines regularly calibrated and records maintained? 燙襯質量是否可接受，機器是否定期較準和維護并保存記錄？
Cutting	11	Are bulk cut goods and trims, designated for either internal or off-premise handling (such as sewing, laundry, embroidery, printing), transported in a well-organized and protected manner? 在內部或外部處理（如縫制、水洗、繡花、印花）的產品和輔料在轉送或運輸過程當中是否有序且受到保護？
Cutting	12	Is there metal/ needle control policy implemented? 是否實施金屬和利器控制程序？
Cutting	13	Are all machines in good conditions/ setting and maintenance? Wiring? 機器是否狀況良好并定期維護？
Cutting	14	Is the molding process in consistent setting and operating? 沖壓過程是否持續設定和運行？

如果企業想做驗廠輔導，不妨考慮一下創思維驗廠之家，創思維驗廠之家是專業的驗廠輔導公司，已經為全國各地上萬家企業服務過，在全國多處設有辦事處，會就近安排老師進場輔導，我們的輔導原則是幫助企業通過驗廠，深圳市創思維是一家正規專業的驗廠咨詢、驗廠輔導、認證輔導公司，一切以合同條款為準，不亂收費，并盡可能為企業節約成本，通過后付款！